Show All
Show Answers
Show Open Questions
Show Most Popular

Topic: Chimneys & fireplaces

Christina N asked:

Apr 4, 2020

Jeff Ainslie of Ainslie Group PRO answered:

Apr 16, 2020

Find a bracket that will span the columns. Drill and insertlead anchors into the brick at the correct locations for the connecting fasteners.

Christina N asked:

Apr 4, 2020
Apr 7, 2020

I would build a stud wall and get rid of the recessed niche. Once done you will have plenty of support in securing the TV mount. 

Jul 20, 2018

Dean Conners answered:

Sep 16, 2018

You can proform both jobs at the same time if you are good at what you do. I have in the past grinded a Grove in the brick chimney all four sides then used a brake to bend a little half inch lip on the top of my flashing metal flashing into massonary Grove then caulked you will never ever have to worry about again in your lifetime Only reason I did massonary work first is because I didn't want to get my shingles all dusted.

Jul 20, 2018

Jeff Ainslie of Ainslie Group PRO answered:

Sep 6, 2018

The masonry work should be performed prior to repairs to the existing roofing, unless the roof is leaking, whereupon you may need to make intermediate repairs to stop the leaking while the masonry work is performed.

Jul 20, 2018
Jul 27, 2018

Definitely before you do the roof, masonary work and any flashing around the chimney should be done prior to starting on the roofing.

Jul 20, 2018
Jul 23, 2018

Our recommendation would be to do the massonry work first and then roofing for a few different reasons.

1.This gives the masons freedom to step and walk on the roof without causing damage to the new shingles. 

2. You will want to make sure the new flashing that is intstalled around the chimney is installed correctly, accounting for any masonry changes and is not damaged due to installation.

3. Ultimately, that the new roof is not damaged and that the warranty does not get voided. 

Jul 20, 2018

Shannon Alberts answered:

Jul 21, 2018

Each case is unique but in general, the chimney should be done first. Special attention should be paid to the roof flashings around the chimney.  If the flashings are behind the stone then make sure they extend far enough into the shingles so the new roof can be flashed properly. If the flashings are surface mounted and there is a counter flashing then the roofer should have no problem making the chimney base watertight   

Nov 28, 2016

If you want an efficient fireplace, I recommend a full insert (sealed-combustion) that runs a new vent pipe, typically up your existing chimney. Hire a professional installer from a local fireplace company to do this. 

There are also options to retrofit a "gas log" in an existing fireplace, but there are several issues with this. Typically, if you have an open hearth without doors that seal tightly closed (with a gasket) then you are going to put more energy up the chimney than actually radiates out into the room.

Margot G asked:

Dec 13, 2016

Ryan Gregory answered:

Dec 14, 2016

Both, more than likely. The mason should replace the masonry products and the roofer should work with the mason to achieve a regletted counterflashing and flash the roof under counterflashings.

Nov 28, 2016
Nov 30, 2016

There are a very wide veriety of gas fireplace inserts.  

1. Check with the city to see what you can install.  Some cities are now requiring sealed units

2. Do not try runing a gas line by yourself.  Hire a licensed plumber to do it.

3. http://www.csia.org/?gclid=CL_Qk-SZ0dACFZBefgodOrUNRA Contact a CSIA certified chimney sweep to help you install. 

Thanks

Philip Anderson

HDR Remodeling Berkeley Ca

Are you a building professional?

Why not answer these questions like a pro?

Sign up free