Answers

It depends,  usually front line questions are resolved via the dealer you purchased the windows through who can determine if its an install or product issue.  you can always escelate directly with teh manufature but depending on the issue they may refer you back to the dealer.

Flashing is an essential component for any window installation.  This is part of the system which protects from water intrusion and structural deterioration.  There may be gaps between your framing or old frame and replacment window frame.  These are typically filled with insulation (usually foam) for energy conservation and to prevent drafts.

Simplified / general answer above.  As with most construction / improvement details, doing it right depends on products, conditions, and is more complex than a two or three line answer can fully describe.  Your best assurance of having it done right is to engage a responsible and experienced contractor.

Good afternoon-

An obscure vinyl slider would be an ideal option.

The difference between new construction and replacement is how much of the existing material they remove/replace, and how the windows are secured to the opening.

In new construction, they remove everything on both sides of the wall, interior and exterior. In replacement, they only remove the inside trim and the window box. I think I have that right? New construction allows you to really look at both the interior and exterior of the opening and make sure you don't have dry rot, make corrections to square/plumb/etc, and nail directly into whatever all that stud/framework stuff is called, but can cause minor/cosmetic damage to the exterior, esp to stucco. Replacement is just removing the interior trim, popping out the old window box and popping in the new one. In my case, they even used the old trim, just nailed it back up and caulked around it.

I had my windows popped out and replaced, primarily because I'm in a 65yo stucco rancher in an area that did a lot of building with redwood. Conventional wisdom says that is exactly the kind of house you should do a new construction installation, rip everything out and have a good look around, but I know I'm only going to be here until my kids graduate from college and when I sell the house it will be razed for a McMansion, like every other house on my block. I just need to get another 10 years out of it, I don't want to put a single $ in I don't have to.

Two things I did not anticipate:

One, my installation did NOT include any touch-up type work, I was responsible for any cosmetic touch-up repair and repainting of interior wall and trim affected by the replacement.

Two, when you put dual-pane acrylic windows where there used to be single-pane wood, you lose nearly all of the interior casing/frame/jamb, whatever you call that part that you would use for an "inside mount" of any kind of shade. I didn't realize I wouldn't be able to use any of the pleated, honeycomb or black-out shades I'd just ordered...

The window (frame) surface is cold, but the air in the apartment is humid. Humid air condenses on a cold surface (when it drops below the dewpoint temperature).

So you can either make the window frame surface warmer, or you can make the air less humid.

Another approach to making the air less humid is to run the air-conditioner, but that makes the house very cold. The dehumidifier usually makes the air warmer, so it's probably preferred, although way less capacity. Some fancy houses have dedicated whole house dehumidifiers (but maybe they also have better windows!).

Window films (the type that shrink with a hair-dryer) attached to the window trim/casing can keep the humid inside air away from the cold surfaces. Added bonus of keeping cold air leaking through windows out of the house.

Looks like this may have been someone's remedy for a deteriorated / rotten mud sill (the flat wooden plate which sits atop the foundation wall, upon which the joists bear).  If that is the case, it is possible that you might be able to remove the latter obstruction if one can restore the proper / original condition over the window.  That would want to be examined and undertaken by a professional.

As with any such thing, it is difficult to say for sure without a full on-site examination by a home imporvement professional with structural knowledge and experience in these types of repairs.

You can more than likely call the manufacturer that made the window and just have a replacement sash made.

Its sounds like you have a double hung window that slides up and down check to see if the outer top window can slide up then lock it. If the glass is sperating from the frame you can take it to a glass replacement company and they will fix the frame and glass if not vinyl welded

I would recommend replacing the window.

sealing or adding any aftermarket seals would most likely sacrifice operation 

The glass package and the insulation of the window are the most important. The best window would be quadriple or triple pane window with foamfilled sashes and krypton or argon gas inbetween the glass. The dense gas keeps the cold air out in the winter and the hot air out in the summer. The foam filled sashes keep the insulation like your walls. Also choose vinyl over wood for better insulation, 

the most important thing you need to make sure you have is a highly rated low-e window. low -e will reflect the solar rays away from the inside of your home so it doesn't heat up during the summer or direct sun etc and during the winter it works in the opposite manor. winter it will keep the heat inside your home keeping your house comfortable. there are many good brands of windows like Andersen, Western, Hurd, Marvin, Eagle (andersen), just to make a few. be sure and do plenty of research and get estimates from. 4-5 companies and compare dont just get estimates from 1 or 2 companies. good luck. 

Check the weepholes and make sure they are not clogged. These holes allow water to drain outside of the window, and are on both sides of the window. If they are clogged then the water will drain wherever it can - inside your walls and house. When the window is closed, you are making it harder for the water to get inside. I suggest taking the tip of a knife and just cleaning them out to see if that helps. 

Is there a leak when it's raining or is it just when the window is open in general? If it's simply when the window is open, then there could be several varying possible reasons as to why the basement leaks, solely when the window remains open. Bad timing, as off putting as that sounds. If it's when the window is open during a rain fall, the window could have lost its seal. Rain could leak in through the wall and then to the basement ceiling. If that's the case, I would recommend a new window seal, or replacing the entire window altogether. If you have further questions or concerns, please feel free to call our office. 403-343-0393. Thank you!

Hey Geoffrey! To leave a review for a GuildQuality member, simply search for the company on our Find a Contractor page, and then click on their profile. In the upper right-hand corner, you will see a button that either says "Add Feedback" or "Leave Review". Once we receive your feedback, we'll mail you a postcard with instructions on how to verify and publish your review. We rely on this verification process to ensure that all feedback published is from actual customers. Let us know if you have any other questions!