Answers

Easily done in one week, no question completed in two

You need a licensed plumber to repair/replace the shower liner. a lot of remodeling companies do not use license plumbers because they are not cheap, and it cuts into there profit. I have been in the plumbing industry for 9 years now. give me call to schedule a free estimate for that leak. 832-557-3293

Hi Cathy,

If you hired a licesned contractor to install the tile, the leaky pan should be under warranty.  I recommend tearing out the entire shower.  Even if you have to pay for the replacement tile, I would not do a repair because tearing out the pan compromises the waterproofing on the walls.  Also, there are many methods of waterproofing the pan area before tile is installed.  We always use the hot mop method.  I would avoidAvoid vinyl liners or Red Gaurd.  These are cheap unreliable options.

Best!

Gregg Cantor

Murray Lampert Design, Build, Remodel

www.murraylampert.com 

Suggest that you find a reputable and skilled tile company.  If it was a vinyl pan, it may be possible (although not ideal) to tear out the floor and lowest 6-12" of wall tile to replace the pan.  It's really something that cannot be easily answered without a close professional examination of the particulars of your shower conditions.

Always seal first and then paint. Why are you re-sealing the corners? 

Seal the corners first, prime, and lastly paint.

Seal first, repaint second, sealant is like caulking used to cover openings.

If the texture is a sparyed-on or roll-on application, there are strippers which will loosen and allow that to be scraped-off.  If it is drywall mud, it's not coming off so easily and you will spend many hours and create a huge mess sanding that down with an orbital sander... then potentially have to re-skim to get the surface ready to accept a good tile job.

We do a lot of backsplashes in existing homes. When the substrate (the surface to which the tile is to be applied) is not satisfactorily flat and smooth, we find that the quickest, cleanest, simplest solution is to remove the drywall and replace with new, moisture-resistant drywall.

That's a very different way to do it, but yes that looks to be your gas shut off.

That is going to vary depending on where you live, the particulars of your home construction, as well as particulars of your planned "pop-top".  Here in Richmond, VA, the structure and exteriors, plus a window or two for a relatively narrow dormer runs in the $10-12,000 range... before you make interior renovations to the bathroom which presumably you may be seeking.

I am guessing that you may be interested in something wide than a 3-4 foot typical dormer.  Well, things become much more structurally complicated in a Cape roof, the wider this pop-top becomes.  As the roof loads become asymmetrical, beams and opposing side structural work will likely become involved (ie: you may have to add structure on the OTHER side of the house, and a beam at the peak of the roof... possibly posting-down to the foundation, to balance the load).  I have seen those go to $30,000+... again, before you start adding in the bath renovations below.  I know; sounds shocking but in order to maintain the structural integrity of your roof, these things may be neccessary.

There are exhaust fans that have a filter and move the air in the bathroom but do not vebt to the outside, this takes cae of the odor. To address the mold you can repaint the bathroom ceiling with a quality paint like Emerald from Sherwin Williams and add a mildew inhibitor to the paint. (it is a liquid that you add to the paint that stops mold from growing) We have used it several times in bathooms and our clients have never called us saying the mold is back. I would also highly recomend leaving the bathroom door open after you shower so that the steam does not stay in the bathoom.

Hi Tammy, it sounds like you likely need a new shower base as Greg has mentioned. The best action would be to correct the problem, since water damage or mold can become very serious issues! A proper shower base should have a slight slope to it. Best of luck!

I don't think so.  Nothing that will last under heat, water and weight.

Philip

The best solution would be to remove the existing shower base and install one that was properly set up to drain. There are different solutions depending on what you have existing there currrently. What kind of material is the shower base?

Hi Tammy,

  It seems you may have an issue with your current shower pan settling, we can definetly help with this.  Please contact us at 1-866-438-2776 and schedule for a technician to help.